|
Addonics 1-Port eSATA 3-Port SATA II RAID5/JBOD PCI Controller The ADSA3R5-E features 1 eSATA and 3 internal SATA ports, allowing the versatility of both the latest External SATA and the industry standard SATA slots. This controller provides your system with RAID5 and JBOD configurations, giving you superior performance using the standard PCI slot. This RAID5/JBOD controller supports configurations of RAID 1, RAID 0, RAID 1+0, RAID5 and JBOD. JBOD combines individual drives into one large volume to show as one drive letter. The External SATA (eSATA) connector also provides a more secured cable connection, improved durability, increased EMI protection and up to 2 meters cable length. With the Addonics optional Disk Array 4SA or 3SA system, you can add a high performance storage system rivaling the traditional SCSI storage at less than half of the cost. Product Features: - SATA II compliant
- Fits standard Desktop case and low profile systems
- PCI compatible
- Supports data transfers of 3Gbits/sec (300MB/sec)*
- 1 eSATA / 3 Internal Serial ATA ports
- Works with any SATA drive
- eSATA connector for a more secure connection, reliability and supports up to 2 meters cable length
- Supports large hard drives of 137 GB or greater
- RAID5/JBOD controller configuration possibilities; RAID 0, RAID1, RAID 1+0, RAID 1+ S, RAID5, JBOD (combines individual drive into one large volume to show as one drive letter)
- Port Multiplier compatible
- Silicon Image chip set SiI 3124
- Hot swap - device can be removed and added without system shut down or restart
- Compatible with Windows 2000, XP, 2003
Specifications: - Compliant with PCI Specification, revision 2.2 and 2.3
- Supports 66 MHz PCI with 32-bit data
- Internal application interface multiplexed to 4 ports
- All registers appear in unified memory space
- Full-chip command completion status accessible with single PCI burst access
- I/O port access to register space
- Low Profile PCI form factor
- High Speed Serial ATA
- Fully compliant with Serial ATA 1.0a and Serial ATA II Extensions to Serial ATA 1.0a Specifications revision 1.1
- Supports SATA II transfer rate of 3G/sec (300 MB/ sec)
- Maximum transfer rate per port (150 MB/sec)*
- Compliant with SATA 1.0 specification
- Supports SATA II First-party DMA commands for Native Command Queuing (NCQ)
- Supports Serial ATA II Port Multiplier 1.0 Specifications revision 1.1
- Plesiochronous, Single PLL architecture, 1 PLL for 4 ports
- 48-bit LBA support
- Four independent DMA channels with 256B FIFO per channel
- Virtual DMA in PCI with serial link in legacy PIO mode
- Supports command buffering for ATA TF shadow registers
- Independent Link, Transport, data FIFO, command fetch, scatter/gather, and command execution
- 31 Commands and Scatter/Gather Tables per Port
- Supports ATAPI devices: CD-ROM, DVD-ROM, etc.
- Supports bootable drive
- Hot-Plug capable
- Supports SATA active signal for 4 separate LEDs
- Built-in firmware RAID support for RAID 0, 1, 10 or 1+S, RAID 5, JBOD
- Supports Spread Spectrum in receiver
- Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host reads and writes
- Low Profile PCI form factor
- Integrated PCI DMA engines
- 32 bit, 33/66MHz fully compliant PCI host interface
- Drivers for Windows 2000, XP and 2003 Server
*The onboard SATA controller chip is SATA II compliant and capable of 3Gbits/sec. Depending on the clock rate of the PCI BUS, the actual data transfer may not be able to reach the 3Gbits/sec data transfer. System Requirements: - PC/AT or Compatible System
- One free PCI slot
- Pentium or greater
- Minimum 32 MB RAM
- 10 MB minimum free hard disk space
- One of the following operating systems: Windows 2000, XP, 2003
Package Contents: 1 eSATA/3 Ports RAID5/JBOD SATA II PCI controller, 1 standard height bracket, 1 low profile bracket, software CD, user guide Warranty: 12 months Click here to compare Addonics Serial ATA Controllers  |
